Kiilto products for your next project

Powdered finishing filler for thin finishing layers on interior walls and ceilings in dry rooms. Mix with water as directed before application. LH is intended for a smooth finish rather than filling deep uneven areas in a single pass. Do not use it as the substrate beneath ceramic tiles or vinyl wall coverings.

Ready-mixed fine filler for finishing walls and ceilings in dry interior rooms before painting or wallpapering. Apply by hand or with suitable spraying equipment in a layer no thicker than 2 mm. Choose XF when a ready-to-use filler suits the job; check the underlying surface and allow previous layers to dry before continuing.

Water-based acrylic sealant for suitable construction joints and surface cracks in dry interiors. It can be painted, making it useful for appropriate repairs before decorating. Exterior applications require painting over the sealant. Match the joint dimensions and adjoining materials to the manufacturer’s instructions; this product is not a substitute for a wet-room waterproofing system.

Water-based multipurpose glue for indoor work involving wood, paper and cardboard. Its D2 classification makes it a choice for appropriate joints in dry indoor conditions. Fit the pieces accurately before applying the glue and keep the joint clamped for the required period. For damp or outdoor work, select a product whose stated use matches the exposure.

D3-class wood glue for suitable timber joints exposed to moisture, including appropriate furniture applications. It can be used outdoors where the joint is protected from weather. Moisture resistance does not make it suitable for continuous immersion. Check the wood, joint fit and expected exposure before choosing the adhesive, then maintain the specified pressure while it bonds.

One-component polyurethane wood adhesive with D4 water-resistance classification for suitable interior and exterior joints. It cures through moisture and is intended for applications requiring a durable bond. Do not use it to bond load-bearing structures. Where one adjoining surface is plastic or metal, check adhesion with a preliminary test rather than assuming compatibility.

Dispersion adhesive for suitable PVC floor coverings and textile coverings with compatible backing. It also suits specified vinyl wall coverings thicker than 0.6 mm. The covering and the absorbency of the substrate determine the bonding method and trowel choice. Check both manufacturers’ installation instructions before starting; do not use this floor-covering adhesive as a general wood glue.

Floor-covering adhesive for suitable LVT, PVC, linoleum and compatible rubber coverings. It can be used over suitable underfloor-heated substrates when the full installation meets the covering and adhesive instructions. Select the bonding method for the actual substrate and covering backing. A click-fit product should only be bonded if its own installation instructions permit that method.

Ready-mixed adhesive for hanging suitable non-woven wallpaper on absorbent or painted surfaces. It can also be used for specified paper-backed wallpapers with their required soaking method. Check the wallpaper roll’s instructions before selecting where to apply the adhesive. It is not intended for all-plastic coverings or for use on plastic substrates.

Ready-mixed paste for paper wallpaper and paper-backed vinyl wallpaper on suitable absorbent or painted surfaces. The backing of the wallpaper matters: the word vinyl alone does not establish compatibility. Check the roll’s hanging and soaking instructions before beginning. Do not use the paste for all-plastic coverings or on a plastic substrate.

Neutral sanitary silicone for suitable flexible joints, material junctions and penetrations in wet areas. This variant is colour 10 traffic white. It cannot be painted over and is not suitable for aquariums or natural stone, including marble. Remove old sealant and prepare the adjoining surfaces properly; a new surface joint does not repair damaged waterproofing behind the tiles.

Transparent, elastic adhesive sealant for suitable fixing and sealing work indoors and outdoors. It is a choice where the appearance of a clear joint matters, including appropriate mirror or glass-block installations. Check the specific surfaces and coatings before bonding. It is not intended for fixing window glass into a frame or for glazing seals.

Elastic mounting adhesive with strong initial tack for suitable wood, concrete, stone and glass applications. It can also be used outdoors and on appropriate damp surfaces. Select it for fixing compatible construction details or trims after checking the material combination. It is not a glazing adhesive; test plastic surfaces and the intended paint before relying on compatibility.

White elastic adhesive sealant for bonding suitable building materials and sealing appropriate moving joints indoors and outdoors. Its use depends on the adjoining materials and the joint design. Test unfamiliar plastics and check paint compatibility before finishing. This 290 ml cartridge requires a suitable application gun; an adhesive sealant alone does not form a complete waterproofing system.

Water-based primer for preparing suitable interior wall and floor substrates before applying Kiilto levelling products. It helps bind residual dust and control substrate absorbency as part of the specified preparation. The dilution depends on both the substrate and the following product. Do not assume a single mixing ratio suits every surface or use the primer to strengthen an unsound base.

Water-based bonding primer used beneath Fibergum waterproofing according to the system instructions. It is suitable for specified wet-room concrete, levelling-compound and construction-board substrates. Dilution varies with the surface, so check the actual substrate before use. The primer is a preparation step and does not provide waterproofing on its own.

Ready-to-use, fibre-reinforced membrane for waterproofing suitable wet-room walls and floors beneath tiles. Use it as part of the specified system, including the required reinforcement and penetration details. It is not intended for swimming pools or sauna steam-room walls. Check substrate suitability, moisture and the compatibility of the drain and system components before starting.

Flexible, non-sagging cement-based adhesive for ceramic tiles and natural stone that is not sensitive to moisture. It can be used in suitable interior and exterior applications and with compatible underfloor-heated substrates. Select the trowel for the tile and base, and check actual adhesive coverage. Do not use it on continuously submerged surfaces such as swimming pools.

Tile grout for suitable wall and floor tiles, supplied in colour 10 traffic white. It is intended for joints 1–6 mm wide and at least 3 mm deep, indoors or outdoors as instructed. Use an appropriate flexible material in movement joints and relevant corners. Tile grout is not waterproofing and is not intended for continuously submerged surfaces such as pools.

Fast-setting floor levelling compound for patching holes, correcting uneven areas and forming suitable floor slopes before subsequent finishing. The stated layer range is 1–30 mm indoors; exterior applications require at least 5 mm and the specified substrate preparation. Prepare the work before mixing, as the compound sets quickly. Finishing and covering times depend on the actual conditions.

Water-based contact adhesive for bonding cork, PVC profiles, laminate, leather and textiles, among other materials. Apply the adhesive to both bonding surfaces.

Moisture-resistant adhesive for glass-fibre fabric, lining wallpaper and suitable thin plastic wall coverings. For dry and wet interior areas.

Moisture-resistant adhesive for glass-fibre fabric, lining wallpaper and suitable thin plastic wall coverings. For dry and wet interior areas.

High initial tack construction adhesive for fixing insulation and acoustic boards and soft construction boards to walls and ceilings.

High initial tack construction adhesive for fixing insulation and acoustic boards and soft construction boards to walls and ceilings.

High initial tack construction adhesive for fixing insulation and acoustic boards and soft construction boards to walls and ceilings.

Ready-to-use gel for removing paper and non-woven wallpaper installed with cellulose- or starch-based paste.

Water-dilutable wallpaper remover for paper-backed wallpaper installed with cellulose- or starch-based paste.

Ready-mixed paste for paper and paper-backed vinyl wallpaper indoors. Not suitable for solid plastic coverings or plastic substrates.

Adhesive for glass-fibre and heavy textile wall coverings in dry interiors. Also suitable for paper-backed vinyl and textile wallpaper. Not suitable for solid plastic coverings.

Adhesive for glass-fibre and heavy textile wall coverings in dry interiors. Also suitable for paper-backed vinyl and textile wallpaper. Not suitable for solid plastic coverings.

Adhesive for glass-fibre and heavy textile wall coverings in dry interiors. Also suitable for paper-backed vinyl and textile wallpaper. Not suitable for solid plastic coverings.

Ready-to-use adhesive for dimensionally stable non-woven wallpaper on absorbent or painted surfaces. For manual or machine application. Not suitable for solid plastic coverings, plastic substrates or glass-fibre fabric.

Ready-to-use adhesive for dimensionally stable non-woven wallpaper on absorbent or painted surfaces. For manual or machine application. Not suitable for solid plastic coverings, plastic substrates or glass-fibre fabric.

Water-mixed starch-based paste for paper wallpaper and lightly embossed paper-backed wallpaper in dry interiors.

Dispersion adhesive for suitable PVC floor coverings and textile coverings with compatible backing. It also suits specified vinyl wall coverings thicker than 0.6 mm. The covering and the absorbency of the substrate determine the bonding method and trowel choice. Check both manufacturers’ installation instructions before starting; do not use this floor-covering adhesive as a general wood glue.